Logic Analyzer FAQ



What do I need in addition to the starter kit?
If you don't want to be restricted to measuring 3,3V signals, you need a level shifter. Such a device can be built using 74LVC4245 or 74ALVTH162244.
How do I connect the signal wires?
Inputs 0-31 can be found on Connector B1 Pin 4-35 in ascending order. Ground is Pin 1. External clock connects to A2 Pin 35. The internal sampling clock is outputted on Connector B1 Pin 40.
How do I set the transfer rate on the board?
This is done using the switches SW1 and SW0. The proper switch settings can be found in the Capture Dialog of the Client. (In Parenthesis behind the transfer rate. H means up.)
How are the LEDs of the 7 segment display mapped to the channels?
Every digit including the dot shows 8 channels. Mapping of digits to channels from left to right: 31-24, 23-16, 15-8, 7-0. Within each digit the channels are ordered (ascending) as follows: The outer LEDs of a digit - starting with the top horizontal bar - in clockwise direction, followed by the middle bar, followed by the dot.


What does the message "Error while invoking apllication:null" mean?
The same as "NoClassDefFoundError: gnu/io/CommPortIdentifier". See below.
What does the message "NoClassDefFoundError: gnu/io/CommPortIdentifier" mean?
The RXTX library is not installed correctly. Ready to use binaries for Windows, Linux and Mac are available here. The included INSTALL file describes which file goes where on which platform. The matching download for other systems can be found on the RXTX home page
How do I install PgsLookAndFeel?
The zip archive contains "PgsLookAndFeel.jar". This files is copied into the ext directory of the JRE. (In Linux the path could be"/usr/lib/java/jre/lib/ext") In case it does not exist, create the file "swing.properties" in the lib directory of the JRE. Add the following line to this file:


How do I add the source in ISE WebPack 8.1?
Create a new project for device XC3S200, package ft256 and speed -4 and add all VHD files and the UCF file using "Add Source".
Why is the synthesizer reporting a max. clock of 50MHz instead of 100/200Mhz?
The maximum clock frequency displayed when synthesizing is the maximum for the clock signal from the crystal oscillator. This is not the signal that is used for sampling.
The frequency is doubled inside the FPGA using a DCM. This gives 100MHz. And the maximum sampling rate of 200MHz is achived using a DDR approach, meaning data is sampled on falling and rising edge of the 100MHz signal.
Wolfgang Meyerle (Tue, 16 Jun 2009):
The code doesn\'t seem to synthetisize on my Spartan 3E Board. I get 174 Errors, any solutions?
Wolfgang Meyerle (Sat, 20 Jun 2009):
Now fixed. I had to remove the second ucf file and to choose the right package (ft256)
Carl (Sun, 8 Jul 2012):
ISE 13.4 is a total pain about DCM and BUFG being on opposite parts of the chip - on my Spartan 3 (Digilent) unit, the crystal osc is on T9 and the external signal is set for D9 - unfortunately, those are on opposite sides of the chip and no common bufg can span them. I selected a different global clock pin (N8), which is on the same side, forced the DCM and the BUFGMUX to be on the same side as pins T9 and N8, finally got a good output. N8 is on pin 4 of A2 connector, replacing the location defined in the project for the external clock input. Works very well now (well, at up to 38400 speed over Win7, Lenovo T420 laptop and USB serial port).

If you are receiving complaints about timing issues from the placement of the DCM or BUFG or input, specify INST "......" LOC=xxxx to get Instcore/BUFGMUX or Instclockman/DCMbaseclock to their desireable locations (e.g BUFGMUX3 for the buffer)
(Mon, 3 Mar 2014):
RXTX home page does not seem to exist anymore....
josh (Sun, 21 Jun 2015):
"What does the message "NoClassDefFoundError: gnu/io/CommPortIdentifier" mean?"

both the links for the 'fix' are invalid... dead project?
Craig A (Wed, 29 Jul 2015):
I found RXTX for Java (required to find the serial port) at http://fizzed.com/oss/rxtx-for-java
PicoPi (Mon, 9 Jan 2017):
How the hell do you install the client software on Windows?
Compiling crap is for Linux losers.
Enter new comment:

The comment will only be accepted when the following question is answered correctly:
How many dwarfs are there in snow white and the seven dwarfs?

(Dear handmade spam sender: The URL will only be linked to after my approval, which you will not get.)